NIMI Mock Test – ITI Turner 1st Year

nimi mock test iti turner

Free Bharat skill NIMI mock test, NCVT ITI exam study material, notes, and  latest job and career notifications.Bharat skills  Nimi Question Bank  ,DGT syllabus available here

NIMI Mock Test - ITI Turner

ITI की Exam Online होती है जिसमे Objective प्रश्न पुछे जाते है अधिकतर प्रश्न Nimi Question bank से ही आते है जिनकी प्रेक्टिस आप NIMI Mock Test  से  कर सकते है

ITI Nimi Mock Test   नीचे दिए गये हैं |

1st Year Topic

NCVT Online Exam में NIMI Mock Test का महत्व

NCVT Online Exam की तैयारी में NIMI Mock Test एक बहुत ही महत्वपूर्ण टूल है, खासकर ITI Turner ट्रेड के विद्यार्थियों के लिए। यह परीक्षा के वास्तविक माहौल का अनुभव देता है और तैयारी को मजबूत बनाता है।

nimi mock test iti turner

Occupational Safety

कुल प्रश्न - 50

समय - 60 मिनट

1 / 8

1. केन्द्र पंच का समाविष्ट कोण कितना होता है (What is the included angle of a center punch)

2 / 8

2. बेच वाइस की बाडी किस साम्रगी की बनी होती है (What material is the body of the selling vice made of?)

3 / 8

3. बिच वाईस की बॉडी किस सामग्री की बनी होती है? (What material is the body of a Beach Vice made of?)

4 / 8

4. फाइल की सामगी क्या हैं (what are the contents of the file )

5 / 8

5. कौन सा कोण किसी ‌ट्विस्ट ड्रिल में कर्तन धार पर रेक कोण को व्यक्त करेगा? (Which angle will represent the rake angle at the cutting edge in a twist drill?)

6 / 8

6. किसी मानक ड्रिल के लिए सामान्य लिप क्लीयरेंस कोण कितना होगा? (What is the normal lip clearance angle for a standard drill?)

7 / 8

7. टीम वर्क किस से संबंधित है? (What is teamwork related to?)

8 / 8

8. प्राथमिक चिकित्सा से संबंधित स्वर्णिम समय कौनसा है? (What is the golden hour for first aid?)

Your score is

The average score is 0%

0%

nimi mock test iti turner

Basic Fitting

कुल प्रश्न - 50

समय - 60 मिनट

1 / 34

1. Which is used to mark the center of a round rod? (किसका उपयोग वृत्ताकार छड़ के केंद्र को चिह्नित करने के लिए किया जाता है?)

2 / 34

2. Which is the blank size M10 x1.5mm of external thread? (बाहरी थ्रेड के लिए ब्लैंक साइज M10 x 1.5 मिमी क्या है?)

3 / 34

3. Which type of chisel is used for squaring materials at the corners and joints? (कोनों और जोड़ों पर सामग्री को वर्गाकार बनाने के लिए किस प्रकार की छेनी का उपयोग किया जाता है?)

4 / 34

4. What is the point angle of cold chisel to cut aluminium? (एल्युमिनियम को काटने के लिए कोल्ड छेनी का पॉइंट एंगल क्या होता है?)

5 / 34

5. Which type of chisel is used to cut key ways? (की-वे काटने के लिए किस प्रकार की छेनी का उपयोग किया जाता है?)

6 / 34

6. Which part of the universal surface gauge is used for fine adjustment? (यूनिवर्सल सरफेस गेज का कौन सा भाग फाइन एडजस्टमेंट के लिए उपयोग किया जाता है?)

7 / 34

7. Which punch is used for locating center of the hole? (छेद के केंद्र का पता लगाने के लिए किस पंच का उपयोग किया जाता है?)

8 / 34

8. Which is used to mark the center of a round rod? (किसका उपयोग वृत्ताकार छड़ के केंद्र को चिह्नित करने के लिए किया जाता है?)

9 / 34

9. Which grade of file is used for heavy reduction of material? (सामग्री को अधिक मात्रा में काटने के लिए किस श्रेणी की फाइल का उपयोग किया जाता है?)

10 / 34

10. Which file is used for filing surfaces at right angle on already finished surface? (पहले से तैयार सतह पर समकोण पर सतहों को घिसने के लिए किस फाइल का उपयोग किया जाता है?)

11 / 34

11. What is the cut of file used for deburring the job on lathe? (लेथ मशीन पर जॉब से बर्र हटाने के लिए किस प्रकार की फाइल का उपयोग किया जाता है?)

12 / 34

12. Which type of tap wrench is used to minimize the damage of taps? (नल को कम से कम नुकसान पहुंचाने के लिए किस प्रकार के नल रिंच का उपयोग किया जाता है?)

13 / 34

13. What type of tap wrench is used in restricted places? (प्रतिबंधित स्थानों में किस प्रकार के टैप रिंच का उपयोग किया जाता है?)

14 / 34

14. Which tool is used for cutting internal thread? (आंतरिक थ्रेड काटने के लिए किस उपकरण का उपयोग किया जाता है?)

15 / 34

15. Which type of vice is used for marking of small jobs on the surface plate? (सरफेस प्लेट पर छोटे-छोटे निशान लगाने के लिए किस प्रकार के वाइस का उपयोग किया जाता है?)

16 / 34

16. Which type of vice has a trigger for opening the movable jaw? (किस प्रकार के वाइस में चल जबड़े को खोलने के लिए ट्रिगर होता है?)

17 / 34

17. Which portion of a hammer head is not hardened or left soft? (हथौड़े के शीर्ष का कौन सा भाग कठोर नहीं किया जाता या नरम ही रहता है?)

18 / 34

18. What is the accuracy of measurement by a try square? (ट्राई स्क्वायर द्वारा माप की सटीकता क्या है?)

19 / 34

19. What is the included angle of prick punch used for marking light punch marks needed to position dividers? (डिवाइडर को सही जगह पर रखने के लिए आवश्यक हल्के पंच के निशान लगाने के लिए उपयोग किए जाने वाले प्रिक पंच का शामिल कोण क्या है?)

20 / 34

20. What is the included angle of center punch? (सेंटर पंच का अंतर्विभाजित कोण क्या है?)

21 / 34

21. Which is the internal part of a bench vice? (बेंच वाइस का आंतरिक भाग कौन सा है?)

22 / 34

22. What is the body material of bench vice? (बेंच वाइस किस सामग्री से बना होता है?)

23 / 34

23. What is the specification for shape of file? (फाइल के आकार के लिए क्या विशिष्टताएँ हैं?)

24 / 34

24. Turner - 1st Semester - Module 2 : Basic Fitting

25 / 34

25. Which angle determines the rake angle at the cutting edge of twist drill? (ट्विस्ट ड्रिल के कटिंग एज पर रेक एंगल किस कोण द्वारा निर्धारित होता है?)

26 / 34

26. What is the normal lip clearance angle for standard drill? (स्टैंडर्ड ड्रिल के लिए सामान्य लिप क्लीयरेंस एंगल क्या होता है?)

27 / 34

27. What is the drill point angle for drilling brass? (पीतल में छेद करने के लिए ड्रिल पॉइंट का कोण क्या होना चाहिए?)

28 / 34

28. Which angle is preventing the cutting edge from rubbing action? (कौन सा कोण धार को रगड़ने से रोक रहा है?)

29 / 34

29. यूनिवर्सल सफेस गेज का कौन सा भाग सूक्ष्म समायोजन के लिए किया जाता है? (Which part of the universal surface gauge is used for fine adjustment?)

30 / 34

30. किस पंच का प्रयोग छिद्र के अंकन मे किया जाता हैं (Which punch is used for marking holes)डांंट पंच (Dante Punch)

31 / 34

31. किसका प्रयोग बेलनाकार उड़ का केंद्र निकलने के लिए किया जाता है (Which is used to find the center of a cylindrical shaft?)

32 / 34

32. पहले से तैयार सतह की समकोण पर सतह बनाने के लिए प्रयोग की जाने वाली फाइल है? (The file used to create a surface at right angles to a previously prepared surface is?)

33 / 34

33. सरफेस प्लेट पर छोटे कायों के अंकन के लिए किस वाईसका प्रयोग किया जाता है (Which vice is used for marking small jobs on a surface plate?)

34 / 34

34. किस वाईस में चाल जबड़े को खोलने के लिए ट्रिगर दिया जाता है? (In which vice is the trigger provided to open the move jaw?)

Your score is

The average score is 0%

0%

nimi mock test iti turner

Lathe Accessories

कुल प्रश्न - 55

समय - 60 मिनट

1 / 55

1. What is the use of gap bed lathe? (गैप बेड लेथ का क्या उपयोग है?)

2 / 55

2. Which type of thread cut on the screw shaft of an independent chuck? (इंडिपेंडेंट चक के स्क्रू शाफ्ट पर किस प्रकार की थ्रेडिंग की जाती है?)

3 / 55

3. What is the purpose of back gear unit in cone pulley headstock of a lathe? (लेथ मशीन के कोन पुली हेडस्टॉक में बैक गियर यूनिट का उद्देश्य क्या है?)

4 / 55

4. What is the swing over bed? (बिस्तर के ऊपर लगा झूला क्या होता है?)

5 / 55

5. What is the purpose of square slot provided on the top of the pinion of a 3 jaw chuck is? (तीन जबड़े वाले चक के पिनियन के शीर्ष पर प्रदान किए गए वर्गाकार स्लॉट का उद्देश्य क्या है?)

6 / 55

6. Which part of center lathe make angular movement? (सेंटर लेथ का कौन सा भाग कोणीय गति करता है?)

7 / 55

7. Which material is used for marking lathe bed? (लेथ बेड पर मार्किंग के लिए किस सामग्री का उपयोग किया जाता है?)

8 / 55

8. Which work holding device of lathe is require to balance for irregular job? (अनियमित आकार के कार्य को संतुलित करने के लिए खराद मशीन के किस कार्य धारण उपकरण की आवश्यकता होती है?)

9 / 55

9. Where will be using the angle plate and counter weight? (एंगल प्लेट और काउंटर वेट का उपयोग कहाँ किया जाएगा?)

10 / 55

10. Which work holding device is used to hold irregular shaped work? (अनियमित आकार के वर्कपीस को पकड़ने के लिए किस वर्कपीस होल्डिंग डिवाइस का उपयोग किया जाता है?)

11 / 55

11. Which work holding device is used to hold irregular shaped work? (अनियमित आकार के वर्कपीस को पकड़ने के लिए किस वर्कपीस होल्डिंग डिवाइस का उपयोग किया जाता है?)

12 / 55

12. Which method of holding is used for lengthy work to avoid over hanging? (लंबे समय तक काम करते समय लटकने से बचने के लिए पकड़ने की कौन सी विधि का उपयोग किया जाता है?)

13 / 55

13. Which one of the below is a work holding device? (नीचे दिए गए विकल्पों में से कौन सा कार्य धारण करने वाला उपकरण है?)

14 / 55

14. Which accessory is used in between center work? (सेंटर वर्क के बीच में कौन सी सहायक सामग्री का उपयोग किया जाता है?)

15 / 55

15. Which one of the below accessory has provided ‘U’ slot? (नीचे दिए गए सहायक उपकरणों में से किसमें 'U' आकार का स्लॉट दिया गया है?)

16 / 55

16. Where the driver pin is used? (ड्राइवर पिन का उपयोग कहाँ किया जाता है?)

17 / 55

17. Turner - 1st Semester - Module 3 : 1.Lathe Accessories

18 / 55

18. How many gears are assembled in tumbler gear mechanism? (टंबलर गियर मैकेनिज्म में कितने गियर असेंबल किए जाते हैं?)

19 / 55

19. Which type taper is provided at the hollow end of the tailstock barrel/spindle? (टेलस्टॉक बैरल/स्पिंडल के खोखले सिरे पर किस प्रकार का टेपर प्रदान किया जाता है?)

20 / 55

20. Which part of lathe slides over the bed ways between headstock and the tailstock? (लेथ का कौन सा भाग हेडस्टॉक और टेलस्टॉक के बीच बेड वेज़ पर स्लाइड करता है?)

21 / 55

21. Which part of carriage is only for possible manual operation? (गाड़ी का कौन सा हिस्सा केवल हाथ से चलाने के लिए है?)

22 / 55

22. Which part of the lathe is ‘H’ shaped cast iron on the bed ways? (लेथ के किस भाग में बेड वेज़ पर 'H' आकार का कच्चा लोहा लगा होता है?)

23 / 55

23. Which part of screw rod of 4 jaw chuck permits the screws to rotate but not to advance? (चार जबड़े वाले चक के स्क्रू रॉड का कौन सा भाग स्क्रू को घूमने की अनुमति देता है लेकिन आगे बढ़ने की नहीं?)

24 / 55

24. What is the angle between the adjustable jaws of a three jaw chuck? (तीन जबड़ों वाले चक के समायोज्य जबड़ों के बीच का कोण क्या है?)

25 / 55

25. Which material used of manufacturing crown wheel of a three jaw chuck? (तीन जबड़े वाले चक के क्राउन व्हील के निर्माण में किस सामग्री का उपयोग किया जाता है?)

26 / 55

26. What is the material of jaws of 3 jaw chuck? (तीन जबड़े वाले चक के जबड़े किस सामग्री से बने होते हैं?)

27 / 55

27. Which material is used to make back plate of a three jaw chuck? (तीन जबड़े वाले चक की बैक प्लेट बनाने के लिए किस सामग्री का उपयोग किया जाता है?)

28 / 55

28. Which material is to used make body of three jaw chuck? (तीन जबड़े वाले चक का ढांचा बनाने के लिए किस सामग्री का उपयोग किया जाता है?)

29 / 55

29. Which jaw of 3 jaw chuck is used to hold hollow job? (तीन जबड़े वाले चक के किस जबड़े का उपयोग खोखले जॉब को पकड़ने के लिए किया जाता है?)

30 / 55

30. Which is 3 jaw chuck? (कौन सा 3 जबड़े वाला चक है?)

31 / 55

31. Which is four jaw chuck? (फोर जॉ चक कौन सा है?)

32 / 55

32. What is an accuracy of an independent four chuck in metric system? (मीट्रिक प्रणाली में स्वतंत्र चार चक की सटीकता क्या है?)

33 / 55

33. What is the name of the part ‘X’? (भाग ‘X’ का नाम क्या है?)

34 / 55

34. What is the inclined angle of dead center conical point? (शंक्वाकार बिंदु के डेड सेंटर का झुकाव कोण क्या है?)

35 / 55

35. Where is the dead center fixed on lathe? (लेथ मशीन पर डेड सेंटर कहाँ निर्धारित किया जाता है?)

36 / 55

36. What is the name of the center accommodates in the main spindle sleeve? (मुख्य स्पिंडल स्लीव में स्थित केंद्र का नाम क्या है?)

37 / 55

37. What type of taper provided on the shank of lathe center? (लेथ सेंटर के शैंक पर किस प्रकार का टेपर दिया जाता है?)

38 / 55

38. What is the name of the center with a carbide tip is brazed into an ordinary steel shank? (साधारण स्टील के शाफ्ट में कार्बाइड टिप को सोल्डर करके लगाए गए केंद्र का नाम क्या है?)

39 / 55

39. Which mechanism is also called as reversing gear unit? (किस तंत्र को रिवर्सिंग गियर यूनिट भी कहा जाता है?)

40 / 55

40. गैप बेड लेथ की क्या उपयोगिता है? (What is the use of gap bed lathe?)

41 / 55

41. स्वतंत्र चक की स्क्रू शाफ्ट पर किस प्रकार की चूड़ी कटी होती है? (What type of thread is cut on the screw shaft of a free chuck?)

42 / 55

42. लेथ के बेड के ऊपर रखे कौन से ढलवा लौहे के बने भाग का आकार H के समान होता है? (Which cast iron part placed on the bed of the lathe is shaped like H?)

43 / 55

43. स्विंग ओवर बेड क्या है (What is a swing over bed?)

44 / 55

44. चार जबड़े वाली चक की पंच छड का कौन सा भाग पैच को घुमने तो देता है किन्तु आगे बढ़ने की अनुमति नहीं देता है? (Which part of the punch rod of a four-jaw chuck allows the patch to rotate but not to move forward?)

45 / 55

45. तीन जबड़े वाली चक के समायोजित जबड़ों के बीच का कोण होता है? (The angle between the adjusting jaws of a three jaw chuck is?)90° (90° )

46 / 55

46. तीन जबड़े वाली चक के पिनियन के शीर्ष में वर्गाकार खांचे का क्या उद्देश्य है? (What is the purpose of the square groove in the head of the pinion of a three jaw chuck?)

47 / 55

47. केन्द्रों के बीच खराद के दौरान किस युक्ति का प्रयोग कार्य को घुमाने में किया जाता है? (Which device is used to rotate the work between centers during lathe?)

48 / 55

48. २० जैध कैरिएर की टेल का क्या उद्‌देश्य होता है? (20 What is the purpose of the carrier's tail?)

49 / 55

49. अनियमित आकार के कायों को पकड़ने के लिए किस कार्य धारण उपकरण का उपयोग किया जाता है? (Which work holding device is used to hold irregularly shaped workpieces?)

50 / 55

50. कार्य और कैरिएर की क्लैपिंग के दौरान। हान टुकड़ों के रूप में बीच में उपलब्ध कराकर किसका बचाव किया जाता है? (During clapping of work and career. What is defended by providing the middle in the form of Han pieces?)

51 / 55

51. कौन सा कैरिएर मे V यूवेस होते है तथा वर्गाकार अनुप्रस्थ काट एवं छोटे व्यास को पकड़ने के काम आता है? (Which carrier has V-tubes and is used to hold square cross section and small diameter?)

52 / 55

52. कौन सा भाग कंपाउंड स्लाइड की बजाय कंपाउंड रेस्ट में अस्सेम्ब्ल होता है? (Which part is assembled into a compound rest instead of a compound slide?)c

53 / 55

53. सहायक का उपकरण का नाम क्या है (what is the name of the assistive device)

54 / 55

54. लेथ केंट की शंक में दिए गए टेपर का प्रकार है (The type of taper given in the shank of lathe cant is)

55 / 55

55. किस तंत्र को प्रतिवती गियार इकाई भी कहा जाता है? (Which system is also called counter gear unit?)

Your score is

The average score is 0%

0%

nimi mock test iti turner

Lathe Cutting Tools

कुल प्रश्न - 50

समय - 60 मिनट

1 / 24

1. What is the cause of glazing? (सतह पर चमक आने का कारण क्या है?)

2 / 24

2. What will happen if too much side relief in parting tool? (पार्टिंग टूल में बहुत अधिक साइड रिलीफ होने पर क्या होगा?)

3 / 24

3. Why the carbide can NOT be used as solid bit? (कार्बाइड को सॉलिड बिट के रूप में क्यों नहीं इस्तेमाल किया जा सकता?)

4 / 24

4. Why the side relief angle is provided? (साइड रिलीफ एंगल क्यों प्रदान किया जाता है?)

5 / 24

5. What is the purpose of side clearance given on turning tool? (टर्निंग टूल पर दी गई साइड क्लीयरेंस का उद्देश्य क्या है?)

6 / 24

6. Why the rake angle is provided? (रेक एंगल क्यों दिया जाता है?)

7 / 24

7. What is angle between the side of the cutting edge to top face of the tool width wise? (उपकरण की चौड़ाई के सापेक्ष काटने वाले किनारे और उपकरण के ऊपरी भाग के बीच का कोण क्या है?)

8 / 24

8. Which angle is control the geometry of chip formation? (चिप निर्माण की ज्यामिति को कौन सा कोण नियंत्रित करता है?)

9 / 24

9. Which angle is preventing the parting tool from getting jammed in the groove? (कौन सा कोण पार्टिंग टूल को खांचे में फंसने से रोक रहा है?)

10 / 24

10. Which tool material have poor hardness property? (किस औजार सामग्री की कठोरता का गुणधर्म निम्न होता है?)

11 / 24

11. What is the use of end cutting tool? (एंड कटिंग टूल का क्या उपयोग है?)

12 / 24

12. Which turning tool cutting edge is similar to boring tool? (किस टर्निंग टूल का कटिंग एज बोरिंग टूल के कटिंग एज के समान होता है?)

13 / 24

13. What is angle formed between the side cutting edge and a line perpendicular to the tool axis? (साइड कटिंग एज और टूल एक्सिस के लंबवत रेखा के बीच बनने वाला कोण क्या है?)

14 / 24

14. Which among the tool material belongs to non metallic tool material? (औजार बनाने की सामग्री में से कौन सी सामग्री अधात्विक औजार सामग्री की श्रेणी में आती है?)

15 / 24

15. Which property of the cutting tool the amount of hardness possessed by a material at normal temperature? (काटने वाले औजार का कौन सा गुण सामान्य तापमान पर किसी पदार्थ की कठोरता की मात्रा को दर्शाता है?)

16 / 24

16. What is the property of tool material to resist sudden shock load? (अचानक लगने वाले झटके और भार को सहन करने के लिए उपकरण सामग्री का क्या गुण होता है?)

17 / 24

17. Which is the example of ferrous tool material? (लौह धातु से बने औजारों की सामग्री का उदाहरण कौन सा है?)

18 / 24

18. Which property avoid the breakage of cutting edge of tools? (कौन सा गुण औजारों की धार को टूटने से बचाता है?)

19 / 24

19. चौड़ाई पर कर्तन धार के साइड और शीर्ष फलक के बीच बना कोण होता है (Width is the angle formed between the side and top face of the cutting edge.)

20 / 24

20. कोण सा कोण पटिंग औजार को यूव में फंसने से बचाता है? (Which angle prevents the putting tool from getting stuck in the uv?)

21 / 24

21. किस औजार सामग्री का कठोरता गुण निम्न है? (Which tool material has low hardness property?)

22 / 24

22. किस खराद औजार की कर्तन धार बोरिंग औजार के समान है? (The cutting edge of which lathe tool is similar to that of boring tool?)

23 / 24

23. एंड कर्तन औजार का उपयोग क्या है? (What is the use of end cutting tool? )

24 / 24

24. निम्न में से कौन सी औजार सामयी अधातु औजार सामयी है? (Which of the following tool parts is a non-metallic tool part?)

Your score is

The average score is 0%

0%

nimi mock test iti turner

Vernier Caliper, Micrometer

कुल प्रश्न - 50

समय - 60 मिनट

1 / 10

1. What is the least of an outside micrometer meter having 50 divisions on thimble and pitch of screw in 0.5mm? (एक बाहरी माइक्रोमीटर मीटर का न्यूनतम मान क्या होगा जिसमें थिम्बल पर 50 विभाजन हों और स्क्रू की पिच 0.5 मिमी हो?)

2 / 10

2. Calculate the least count, if 49 main scale divisions are divided into 50 equal parts on the vernier scale? (यदि वर्नियर स्केल पर 49 मुख्य स्केल डिवीजनों को 50 बराबर भागों में विभाजित किया जाता है, तो न्यूनतम माप ज्ञात कीजिए?)

3 / 10

3. Which parts of vernier caliper is used for measuring the width of slot? (स्लॉट की चौड़ाई मापने के लिए वर्नियर कैलिपर के किन भागों का उपयोग किया जाता है?)

4 / 10

4. Which part of the micrometer has marked datum line? (माइक्रोमीटर के किस भाग पर डेटम लाइन अंकित है?)

5 / 10

5. What is the accuracy of an outside metric micrometer? (किसी बाहरी मीट्रिक माइक्रोमीटर की सटीकता क्या है?)

6 / 10

6. Which precision instrument is used to measure the diameter to an accuracy of 0.01mm? (किस परिशुद्ध उपकरण का उपयोग व्यास को 0.01 मिमी की सटीकता तक मापने के लिए किया जाता है?)

7 / 10

7. Which is the material used in manufacture of frame for an outside micrometer? (बाहरी माइक्रोमीटर के फ्रेम के निर्माण में किस सामग्री का उपयोग किया जाता है?)

8 / 10

8. What is the least count of a standard metric vernier caliper? (एक मानक मीट्रिक वर्नियर कैलिपर का न्यूनतम माप क्या है?)

9 / 10

9. Which is the smallest measurement that is possible by vernier caliper? (वर्नियर कैलिपर द्वारा मापी जा सकने वाली सबसे छोटी माप क्या है?)

10 / 10

10. Which material is used in manufacture of anvil for outside micrometer? (बाहरी माइक्रोमीटर के लिए निहाई के निर्माण में किस सामग्री का उपयोग किया जाता है?)

Your score is

The average score is 0%

0%

nimi mock test iti turner

Drills

कुल प्रश्न - 50

समय - 60 मिनट

1 / 36

1. Where the fatty oil is used? (वसायुक्त तेल का उपयोग कहाँ किया जाता है?)

2 / 36

2. Which method is used to lubricate the head stock in modern lathe? (आधुनिक खराद मशीनों में हेड स्टॉक को चिकनाई देने के लिए किस विधि का उपयोग किया जाता है?)

3 / 36

3. Which cutting fluid is used for turning copper? (तांबे की खराद के लिए किस प्रकार के कटिंग फ्लूइड का उपयोग किया जाता है?)

4 / 36

4. Which tool is used to finish a drilled hole manually? (किसी ड्रिल किए गए छेद को मैन्युअल रूप से फिनिश करने के लिए किस उपकरण का उपयोग किया जाता है?)

5 / 36

5. What is the purpose of the square portion provided on the shank of reamer? (रीमर के हैंडल पर दिए गए वर्गाकार भाग का उद्देश्य क्या है?)

6 / 36

6. Which tool is rotated in clockwise direction both when cutting and when with drawing? (काटने और खींचने दोनों ही स्थितियों में किस उपकरण को दक्षिणावर्त दिशा में घुमाया जाता है?)

7 / 36

7. What is the purpose of reducing speed by 3/4th of turning while reaming? (रीमिंग करते समय घुमाव की गति को 3/4 कम करने का उद्देश्य क्या है?)

8 / 36

8. Which drilling machine is used for light duty work? (हल्के कार्यों के लिए किस प्रकार की ड्रिलिंग मशीन का उपयोग किया जाता है?)

9 / 36

9. Which part of the drilling machine helps for the protection of the operator? (ड्रिलिंग मशीन का कौन सा भाग ऑपरेटर की सुरक्षा में सहायक होता है?)

10 / 36

10. Which type of drill is used for drilling brass? (पीतल में छेद करने के लिए किस प्रकार की ड्रिल का उपयोग किया जाता है?)

11 / 36

11. Which coolant oil is not diluted? (कौन सा शीतलक तेल पतला नहीं होता है?)

12 / 36

12. Which portion of the reamer is reduced in diameter below the cutting edge? (कटिंग एज के नीचे रीमर के किस भाग का व्यास कम किया जाता है?)

13 / 36

13. Which portion of the reamer is reduced in diameter below the cutting edge? (कटिंग एज के नीचे रीमर के किस भाग का व्यास कम किया जाता है?)

14 / 36

14. Which material is used for making tap? (नल बनाने के लिए किस सामग्री का उपयोग किया जाता है?)

15 / 36

15. Which drilling machine is capable of drilling up to 12.5 mm diameter? (कौन सी ड्रिलिंग मशीन 12.5 मिमी व्यास तक ड्रिलिंग करने में सक्षम है?)

16 / 36

16. What is the maximum size of drill can be hold in sensitive drilling machine? (संवेदनशील ड्रिलिंग मशीन में अधिकतम किस आकार की ड्रिल लगाई जा सकती है?)

17 / 36

17. What is the maximum size of parallel shank twist drill? (पैरेलल शैंक ट्विस्ट ड्रिल का अधिकतम आकार क्या है?)

18 / 36

18. Which material is used for making drill? (ड्रिल बनाने के लिए किस सामग्री का उपयोग किया जाता है?)

19 / 36

19. Which part of the drill is used for measuring the drill diameter? (ड्रिल के किस भाग का उपयोग ड्रिल के व्यास को मापने के लिए किया जाता है?)

20 / 36

20. What is the point angle of a twist drill for general purpose work? (सामान्य कार्यों के लिए उपयोग होने वाली ट्विस्ट ड्रिल का पॉइंट एंगल क्या होता है?)

21 / 36

21. What is the name of device to hold parallel shank drills? (पैरेलल शैंक ड्रिल को पकड़ने वाले उपकरण का नाम क्या है?)

22 / 36

22. Which factor decides the point angle of a drill? (ड्रिल के बिंदु कोण को कौन सा कारक निर्धारित करता है?)

23 / 36

23. आधुनिक लेथ के हेड स्टॉक में किस स्नेहन विधि का प्रयोग किया जाता है? (Which lubrication method is used in the head stock of modern lathe?)

24 / 36

24. किस कर्तन द्रव्य का प्रयोग तांबे की खराद करने में किया जाता है? (Which cutting fluid is used in turning copper?)

25 / 36

25. किस औजार का प्रयोग ड्रिल किए गए छिद्र को फिनिश करने में किया जाता है ? (Which tool is used to finish the drilled hole?)

26 / 36

26. रीमर की शेक पर वर्गाकार भाग दिए जाने का क्या प्रयोजन है? (What is the purpose of providing square sections on the reamer shake?)

27 / 36

27. रीमर की शेक पर वर्गाकार भाग दिए जाने का क्या प्रयोजन है? (What is the purpose of providing square sections on the reamer shake?)

28 / 36

28. किस औजार का प्रयोग खोदने और निकलने दोनों में दक्षिणावर्त दिशा में घुमाते हुए किया जाता है? (Which tool is used for both digging and digging by rotating it in clockwise direction?)

29 / 36

29. रीमिंग के दौरान खराद्र की तुलना में 3/4 गति रखने का क्या उद्देश्य है? (What is the purpose of keeping the speed 3/4 of the lathe during reaming?)

30 / 36

30. हल्के कामों के लिए कौन सी ड्रिलिंग मशीन प्रयोग की जाती है ? (Which drilling machine is used for light work?)

31 / 36

31. ड्रिलिंग मशीन काकौन सा भाग सक्रियक की सुरक्षा के काम आता है ? (Which part of the drilling machine is used to protect the activator?)

32 / 36

32. किस प्रकार का ड्रिल पीतल में ड्रिल करने के काम आता है? (Which type of drill is used to drill brass?)

33 / 36

33. कौन सा कलेन आयल तनु नहीं होता है? (Which olein oil is not diluted?)

34 / 36

34. रीजर का कौन सा भाग कर्तन धार के नीचे व्यास में कम होला जाता है? (Which part of the ridger is reduced in diameter below the cutting edge?)

35 / 36

35. कोल्ड कोर्जिग और प्लास्टिक डिफोरमेशन से चूड़ी निर्माण की विधि बताइये? (Tell the method of making bangles by cold coring and plastic deformation?)

36 / 36

36. 7/16 नीज वाली ही काटने के लिए वांछित पेज गियर की गणना कीजिये यदि लेथ के लीड स्कू 4 TPI का हो? (7/16 Calculate the required page gear for the same cutting if the lead screw of the lathe is of 4 TPI?)

Your score is

The average score is 0%

0%

nimi mock test iti turner

Fits and Limits

कुल प्रश्न - 50

समय - 60 मिनट

1 / 26

1. Which operation is used to increase the diameter of work slightly to get a press fit? (प्रेस फिट प्राप्त करने के लिए वर्कपीस का व्यास थोड़ा बढ़ाने के लिए किस प्रक्रिया का उपयोग किया जाता है?)

2 / 26

2. What is the speed used for knurling? (नर्लिंग के लिए किस गति का उपयोग किया जाता है?)

3 / 26

3. What is the purpose of knurling operation? (नर्लिंग प्रक्रिया का उद्देश्य क्या है?)

4 / 26

4. What is 6 in the given expression of fit 30H7/g6? (fit 30H7/g6 के दिए गए व्यंजक में 6 का मान क्या है?)

5 / 26

5. Calculate the maximum limit of size from the given data 100+0.015-0.010? (दिए गए डेटा 100+0.015-0.010 से आकार की अधिकतम सीमा की गणना करें।)

6 / 26

6. What is the grade ITO1 related to fit? (फिट के संबंध में ITO1 ग्रेड का क्या महत्व है?)

7 / 26

7. Which one belongs to team work? (इनमें से कौन सा टीम वर्क से संबंधित है?)

8 / 26

8. Calculate the upper deviation from the given
data? 20 +0.008
- 0.005 (दिए गए आंकड़ों से ऊपरी विचलन की गणना करें?

20 +0.008

- 0.005)

9 / 26

9. Which term refers the accuracy of manufacture? (किस शब्द से निर्माण की सटीकता का तात्पर्य है?)

10 / 26

10. What is Knurling? (नर्लिंग क्या है?)

11 / 26

11. What is called the greater of the two limit of sizes? (आकार की दो सीमाओं में से बड़ी सीमा किसे कहते हैं?)

12 / 26

12. What is actual deviation? (वास्तविक विचलन क्या है?)

13 / 26

13. What is the term for extreme permissible size with in that the operator is expected to make? (उस सीमा के भीतर अनुमेय आकार की अधिकतम सीमा को क्या कहते हैं, जिसके भीतर ऑपरेटर से काम करने की अपेक्षा की जाती है?)

14 / 26

14. How external features of a component including which not cylindrical is designated as per BIS? (बेलनाकार न होने वाले घटक की बाहरी विशेषताओं को बीआईएस के अनुसार कैसे नामित किया जाता है?)

15 / 26

15. How external features of a component including which not cylindrical is designated as per BIS? (बेलनाकार न होने वाले घटक की बाहरी विशेषताओं को बीआईएस के अनुसार कैसे नामित किया जाता है?)

16 / 26

16. How external features of a component including which not cylindrical is designated as per BIS? (बेलनाकार न होने वाले घटक की बाहरी विशेषताओं को बीआईएस के अनुसार कैसे नामित किया जाता है?)

17 / 26

17. What is also known as fundamental tolerance? (मूलभूत सहिष्णुता किसे कहते हैं?)

18 / 26

18. What is the system if the shaft is varied to set different class of fit? (यदि शाफ्ट को बदलकर अलग-अलग प्रकार की फिटिंग की जाए तो सिस्टम कैसा होगा?)

19 / 26

19. What is the term if the difference between the maximum limit of size and minimum limit of size? (आकार की अधिकतम सीमा और न्यूनतम सीमा के बीच के अंतर को क्या कहते हैं?)

20 / 26

20. Calculate the tolerance from the given data 20+0.021-0.002? (दिए गए डेटा 20+0.021-0.002 से टॉलरेंस की गणना करें।)

21 / 26

21. Calculate the tolerance of 100e8 shaft from the given data minimum deviation - 72 maximum deviation- 126? (दिए गए आंकड़ों से 100e8 शाफ्ट की सहनशीलता की गणना करें: न्यूनतम विचलन - 72, अधिकतम विचलन - 126?)

22 / 26

22. Calculate the limits of the shaft 20H7/g6 if upper limits is -7 and lower limit is -20? (यदि ऊपरी सीमा -7 और निचली सीमा -20 है, तो शाफ्ट 20H7/g6 की सीमाओं की गणना करें?)

23 / 26

23. BIS के अनुसार किसी बेलन के बाहरी विशेषताओ को किसके बिना नामित नहीं किया (According to BIS, the external features of a cylinder are not named without)

24 / 26

24. किसे मूलभूत सहिष्णुता भी कहा जाता है? (What is also called basic tolerance?)

25 / 26

25. यदि शाफ्ट को विभिन्न श्रेणियों की फिट में बैठने के लिए परिवर्तित किया जाता है तो यह कौन सी पद्धति होगी (If the shaft is modified to fit different categories then what method will it be?)

26 / 26

26. माप की उच्चतम सीमा और निम्नतम सीमा के अंतर को क्या कहते है? (What is the difference between the highest limit and lowest limit of measurement called?)

Your score is

The average score is 0%

0%

nimi mock test iti turner

Taper Turning

कुल प्रश्न - 50

समय - 60 मिनट

1 / 38

1. What should be the heights of gauge block to be built to check the work angle of 30° using 150 mm sine bar? (150 मिमी साइन बार का उपयोग करके 30° के कार्य कोण की जाँच करने के लिए निर्मित किए जाने वाले गेज ब्लॉक की ऊँचाई कितनी होनी चाहिए?)

2 / 38

2. Which method is preferred for producing small length taper with least accuracy? (कम से कम सटीकता के साथ छोटी लंबाई के टेपर बनाने के लिए कौन सी विधि बेहतर है?)

3 / 38

3. Which method is used for turning steep taper? (तीव्र टेपर बनाने के लिए किस विधि का उपयोग किया जाता है?)

4 / 38

4. Why the ball center is preferred in tail stock offset method? (टेल स्टॉक ऑफसेट विधि में बॉल सेंटर को प्राथमिकता क्यों दी जाती है?)

5 / 38

5. What is the purpose of welding accessory? (वेल्डिंग सहायक उपकरण का उद्देश्य क्या है?)

6 / 38

6. What is the main disadvantage of a braze welded joints? (ब्रेज़ वेल्डिंग जोड़ों का मुख्य नुकसान क्या है?)

7 / 38

7. Which welding method is more suitable for joining dissimilar metals readily? (अलग-अलग धातुओं को आसानी से जोड़ने के लिए कौन सी वेल्डिंग विधि अधिक उपयुक्त है?)

8 / 38

8. What is the isolating medium to prevent rapid cooling after brazing a tipped tool? (किसी नुकीले औजार को ब्रेज़िंग करने के बाद तीव्र शीतलन को रोकने के लिए उपयुक्त इन्सुलेटिंग माध्यम क्या है?)

9 / 38

9. How to measure the diameter of the small end of a external taper precisely? (बाहरी टेपर के छोटे सिरे के व्यास को सटीक रूप से कैसे मापा जाए?)Sine bar (साइन बार)

10 / 38

10. How is the “length of sine bar “specified? (“साइन बार की लंबाई” कैसे निर्दिष्ट की जाती है?)

11 / 38

11. Which part of the combination set is used for measuring the angles? (कोणों को मापने के लिए संयोजन सेट के किस भाग का उपयोग किया जाता है?)

12 / 38

12. Convert 8° 44’ into minutes? (8° 44’ को मिनट में बदलें?)c

13 / 38

13. What is the accuracy of the protractor head of a combination set? (एक संयोजन सेट के प्रोटेक्टर हेड की सटीकता क्या है?)

14 / 38

14. Calculate the least count of V.B.P if 20 div on main scale is divided into 12 equal parts (यदि मुख्य तराजू पर 20 डिव को 12 बराबर भागों में विभाजित किया जाए तो न्यूनतम मान (VBP) ज्ञात कीजिए।)

15 / 38

15. What is the purpose of the beveled edges of the rule in a vernier bevel protractor? (वर्नियर बेवल प्रोट्रैक्टर में रूल के तिरछे किनारों का उद्देश्य क्या है?)

16 / 38

16. Which part of the lathe is locked while the form tool method is used for turning taper? (टेपर टर्निंग के लिए फॉर्म टूल विधि का उपयोग करते समय लेथ का कौन सा भाग लॉक किया जाता है?)

17 / 38

17. Which one is the disadvantage of taper turning by compound slide method? (कंपाउंड स्लाइड विधि द्वारा टेपर टर्निंग का एक नुकसान क्या है?)

18 / 38

18. Which is the advantage of taper turning by compound slide method? (कंपाउंड स्लाइड विधि द्वारा टेपर टर्निंग का क्या लाभ है?)

19 / 38

19. Which one is the disadvantage of using tail stock offset method? (टेल स्टॉक ऑफसेट विधि का उपयोग करने का नुकसान क्या है?)

20 / 38

20. Which material is used for making the head of soldering iron? (सोल्डरिंग आयरन का सिर बनाने के लिए किस सामग्री का उपयोग किया जाता है?)

21 / 38

21. Which material is used for making nozzle for gas welding? (गैस वेल्डिंग के लिए नोजल बनाने में किस सामग्री का उपयोग किया जाता है?)

22 / 38

22. How is the filler material distributed in the joint in braze welding? (ब्रेज़ वेल्डिंग में जोड़ में फिलर सामग्री का वितरण कैसे होता है?)

23 / 38

23. What is the use of a sine bar? (साइन बार का क्या उपयोग है?)

24 / 38

24. How many seconds is 1°? (1 डिग्री कितने सेकंड के बराबर होता है?)

25 / 38

25. Select a suitable instrument for measuring angles? (कोणों को मापने के लिए उपयुक्त उपकरण का चयन करें?)

26 / 38

26. Which is the smallest unit of angular measurement? (कोणीय माप की सबसे छोटी इकाई कौन सी है?)

27 / 38

27. Which part is pivoted to the disc of vernier bevel protractor? (वर्नियर बेवल प्रोट्रैक्टर के डिस्क से कौन सा भाग धुरी पर टिका होता है?)

28 / 38

28. Which instrument can measure angle up to an accuracy of 5 minutes? (कौन सा उपकरण 5 मिनट की सटीकता तक कोण माप सकता है?)

29 / 38

29. सामान्य फरिनंग कार्य के लिए किस चूड़ी का प्रयोग किया जाता है (Which bangle is used for general farning work )

30 / 38

30. वर्नियर हाइट गेज का अल्पत्मांक क्या है? (What is the least count of vernier height gauge?)

31 / 38

31. ब्रेजिंग की कौनसी विधि कार्बाइड टिप को शैंक मे ब्रेज करने में प्रयोग होती है (Which method of brazing is used to braze the carbide tip into the shank?)

32 / 38

32. वेल्डिंग के सहायक उपकरणों का क्या उद्‌द्देश्य है? (What is the purpose of welding accessories? )

33 / 38

33. भिन्न धातुओं को शीघ्रता से जोड़ने के लिए उपयुक्त वेल्डिंग प्रक्रिया कौन सी होगी? (Which would be a suitable welding process for quickly joining dissimilar metals?)

34 / 38

34. कॉम्चिनेशन सेंट के किस भाग की कोणीय मापन में प्रयोग किया जाता है (Which part of the combination cent is used in angular measurement?)

35 / 38

35. फॉर्म टूल विधि से टेपर टर्निग के दौरान लेथ का कौन सा भाग लॉक किया जाता? (Which part of the lathe is locked during taper turning by form tool method?)

36 / 38

36. टेल स्टॉक ओफ़्सेट विधि की हानि क्या है? (What is the disadvantage of tail stock offset method?)

37 / 38

37. सोल्डरिंग आयरन का सिरा बनाने के लिए किस सामग्री का प्रयोग किया जाता है? (Which material is used to make the tip of soldering iron?)

38 / 38

38. गैस वेल्डिंग की नोजल बनाने के लिए किस सामग्री का पर्योग किया जाता है? (Which material is used to make nozzle for gas welding?)

Your score is

The average score is 0%

0%

nimi mock test iti turner

Eccentric Turning

कुल प्रश्न - 50

समय - 60 मिनट

1 / 17

1. Which thread is used for general purpose fastening? (सामान्य प्रयोजन के बंधन के लिए किस प्रकार के धागे का उपयोग किया जाता है?)

2 / 17

2. Which carrier with V-groove provided and used to hold small diameter and square sections? (किस प्रकार के वाहक में वी-ग्रूव बना होता है और जिसका उपयोग छोटे व्यास और वर्गाकार खंडों को पकड़ने के लिए किया जाता है?)

3 / 17

3. Which form of thread is widely used for fastening purpose? (बांधने के उद्देश्य से किस प्रकार के धागे का व्यापक रूप से उपयोग किया जाता है?)

4 / 17

4. Which device is used as datum while marking with vernier height gauge? (वर्नियर हाइट गेज से अंकन करते समय किस उपकरण को आधार बिंदु के रूप में उपयोग किया जाता है?)

5 / 17

5. How is the vernier height gauge generally specified? (वर्नियर हाइट गेज को सामान्यतः कैसे निर्दिष्ट किया जाता है?)

6 / 17

6. What is thread element that determine the direction of rotation on screw thread? (पेंच के धागे पर घूर्णन की दिशा निर्धारित करने वाला धागा तत्व क्या है?)

7 / 17

7. How is the vernier height gauge generally specified? (वर्नियर हाइट गेज को सामान्यतः कैसे निर्दिष्ट किया जाता है?)

8 / 17

8. How is the vernier height gauge generally specified? (वर्नियर हाइट गेज को सामान्यतः कैसे निर्दिष्ट किया जाता है?)

9 / 17

9. What is thread element that determine the direction of rotation on screw thread? (पेंच के धागे पर घूर्णन की दिशा निर्धारित करने वाला धागा तत्व क्या है?)

10 / 17

10. How many carriers are available in a set? (एक सेट में कितने कैरियर उपलब्ध हैं?)

11 / 17

11. What is the formula for finding the depth of a BIS metric thread? (बीआईएस मेट्रिक थ्रेड की गहराई ज्ञात करने का सूत्र क्या है?)

12 / 17

12. What is the angle of a BIS metric thread? (बीआईएस मीट्रिक थ्रेड का कोण क्या होता है?)

13 / 17

13. Which thread is recommended for pipe and pipe fittings? (पाइप और पाइप फिटिंग के लिए कौन सा थ्रेड उपयुक्त है?)

14 / 17

14. What is the angle of metric ACME thread ? (मेट्रिक ACME धागे का कोण क्या है?)

15 / 17

15. What is the angle of metric ACME thread ? (मेट्रिक ACME धागे का कोण क्या है?)

16 / 17

16. Which thread is used for general purpose fastening? (सामान्य प्रयोजन के बंधन के लिए किस प्रकार के धागे का उपयोग किया जाता है?)

17 / 17

17. What is the least count of vernier height gauge? (वर्नियर हाइट गेज का न्यूनतम माप क्या है?)

Your score is

The average score is 0%

0%

nimi mock test iti turner

Thread Cutting

कुल प्रश्न - 80

समय - 120 मिनट

1 / 76

1. What is the formula to find out core diameter of external thread by using prisms and micrometer? (प्रिज्म और माइक्रोमीटर का उपयोग करके बाहरी थ्रेड के कोर व्यास का पता लगाने का सूत्र क्या है?)

2 / 76

2. रोलिंग ‌द्वारा चूड़ी निर्माण में कार्य के किस व्यास को बनाये रखा जाता है (Which diameter of work is maintained in bangle manufacturing by rolling?)

3 / 76

3. What is the depth of buttress thread if the pitch is
1.8 mm of 45° angle? (यदि पिच 1.8 मिमी और कोण 45° हो तो बट्रेस थ्रेड की गहराई कितनी होगी?)

4 / 76

4. What is the use of BSW thread? (BSW थ्रेड का क्या उपयोग है?)

5 / 76

5. How many un-numbered divisions on the British chasing dial? (ब्रिटिश चेज़िंग डायल पर बिना नंबर वाली कितनी डिवीजन हैं?)

6 / 76

6. Turner - 2nd Semester - Module 3 :Thread Cutting

7 / 76

7. औजार आयु सूचकांक जाल करने के लिए किसकी जरूरत पडली है? (What is needed to calculate the tool age index?)

8 / 76

8. कर्टन औजार सामग्री वह गुण जो सामान्य ताप की अवस्था में कठोरता की मात्रा दर्शाता है कहलाता है (Curtain tool material The property which shows the amount of hardness at normal temperature is called)

9 / 76

9. Which type of thread is used in screw jack spindle? (स्क्रू जैक स्पिंडल में किस प्रकार के धागे का उपयोग किया जाता है?)

10 / 76

10. What is formula for finding depth of BSW external thread? (BSW एक्सटर्नल थ्रेड की गहराई ज्ञात करने का सूत्र क्या है?)

11 / 76

11. यहडिग व्हील के अपघर्षक कणों के मध्य दहतु के कणों के फस जाने को कहते है? (What is the trapping of metal particles between the abrasive particles of the digging wheel called?)

12 / 76

12. टेप और डाई द्वारा किस प्रकार की चूड़ी उत्पादित की जाती है? (What type of bangles are produced by tape and dye?)

13 / 76

13. Tr वर्ग धागा Tr 40 0 x 7 गहराई 0.01 mm की मामूली निकासी का मामूली व्यास क्या है? (What is the nominal diameter of nominal clearance of Tr square thread Tr 40 0 ​​x 7 depth 0.01 mm?)

14 / 76

14. श्रेड मापन में प्रिज्म प्रयोग किए जाने का क्या उद्देश्य है? (What is the purpose of using prism in shred measurement?)

15 / 76

15. चूड़ी औजार में कौन सा कोण घिस के बनाया जाता है? ( Which angle is made by grinding in bangle tool?)

16 / 76

16. B.S.P चूड़ी का क्या उपयोग है? (What is the use of B.S.P bangle?)

17 / 76

17. कोल्ड फोर्जिंग और प्लास्टिक डिफोरमेशन से चूड़ी निर्माण की विधि बताइये? (Tell the method of manufacturing bangles by cold forging and plastic deformation?)

18 / 76

18. Which terms are needed to calculate tool life index? (टूल लाइफ इंडेक्स की गणना के लिए किन शर्तों की आवश्यकता होती है?)

19 / 76

19. What is the only thread form cut using die head is turret lathe? (टरेट लेथ में डाई हेड का उपयोग करके काटा जाने वाला एकमात्र थ्रेड फॉर्म कौन सा है?)

20 / 76

20. 2.5mm बाली चूड़ी को काटने के लिए वंचित चेंज गियर ( ड्रिवन गियर ) गैर की गणना कीजिए जो यदि लेट के स्क्रू की पिच 5mm हो ड्राइवर 50 दांतों वाला हो (Calculate the required change gear (driven gear) required for cutting 2.5mm earring bangle if the pitch of latch screw is 5mm and the driver has 50 teeth. )

21 / 76

21. Which is the method to produce threads on non metals? (अधातुओं पर धागे बनाने की विधि कौन सी है?)

22 / 76

22. निर्माण की चिप रहित विधि कौन सी है ? ( Which is the chipless method of manufacturing?)

23 / 76

23. टेप और डाई द्वारा किस प्रकार की चूड़ी उत्पादित की जाती है? (What type of bangles are produced by tape and dye?)

24 / 76

24. What is the shape of interchangeable anvils used in screw thread micrometer? (स्क्रू थ्रेड माइक्रोमीटर में उपयोग होने वाले विनिमेय एनविल का आकार कैसा होता है?)

25 / 76

25. चूड़ी कर्तन के लिए गियर अनुपाल का सूत्र क्या है (What is the gear compliance formula for bangle cutting?)

26 / 76

26. शुद्ध आआंतरिक पक्षी निर्माण की विधि कोन सी है? (Which is the method of making pure internal bird?)

27 / 76

27. Which diameter is maintained in a job for making threads by rolling? (रोलिंग द्वारा धागे बनाने के लिए किसी जॉब में किस व्यास को बनाए रखा जाता है?)

28 / 76

28. आआंतरिक धागे के मामूली व्यास को कैसे माप सकते हैं? (How to measure the nominal diameter of an internal thread?)

29 / 76

29. Calculate the driven gear required to cut 4mm pitch thread is a lathe having lead screw of 4mm with driven gear of 60 teeth? (4 मिमी पिच का धागा काटने के लिए आवश्यक ड्राइव गियर की गणना करें यदि लेथ मशीन में 4 मिमी का लीड स्क्रू और 60 दांतों वाला ड्राइव गियर है?)

30 / 76

30. टूल लाइफ डबिंग के लिए कटिंग गति का कितना प्रतिशत कम होता है? (What percentage of cutting speed is reduced for tool life dubbing?)

31 / 76

31. How can measure the minor diameter of a external thread? (किसी बाहरी थ्रेड के लघु व्यास को कैसे मापा जा सकता है?)

32 / 76

32. Calculate the change gear (driven gear) if driver is 50 teeth to cut 2.5mm pitch thread on a job by lathe having a lead screw of 5mm pitch? (यदि ड्राइवर में 50 दांत हैं और उसे 5 मिमी पिच वाले लीड स्क्रू वाले लेथ मशीन पर 2.5 मिमी पिच का थ्रेड काटना है, तो आवश्यक चेंज गियर (ड्रिवन गियर) की गणना कीजिए?)

33 / 76

33. What is the minor diameter of screw thread SQ 62 x 10.8 with depth clearance of 0.12 mm? (0.12 मिमी की गहराई क्लीयरेंस वाले स्क्रू थ्रेड SQ 62 x 10.8 का लघु व्यास क्या है?)

34 / 76

34. गैर धातुओं पर धागे का प्रधान करते है? (Do threads predominate on non-metals?)

35 / 76

35. What type of thread can be produced by a die? (डाई से किस प्रकार का धागा बनाया जा सकता है?)

36 / 76

36. Which is the commonly used method to produce thread on nut? (नट पर थ्रेड बनाने के लिए आमतौर पर कौन सी विधि का उपयोग किया जाता है?)

37 / 76

37. Which method of holding is used for lengthy work to avoid over hanging? (लंबे समय तक काम करते समय लटकने से बचने के लिए पकड़ने की कौन सी विधि का उपयोग किया जाता है?)

38 / 76

38. What is the minor diameter of Trapezoidal screw thread Tr 40 x 7 depth clearance of 0.01 mm? (0.01 मिमी की गहराई क्लीयरेंस वाले ट्रेपेज़ॉइडल स्क्रू थ्रेड Tr 40 x 7 का लघु व्यास क्या है?)

39 / 76

39. डाई द्वारा किस प्रकार की चूड़ी उत्पादित की जाती है? (What type of bangle is produced by dye?)

40 / 76

40. औजार की आयु को बढ़ाने का मुख्य मापदंड क्या है? (What is the main parameter to increase the life of a tool?)

41 / 76

41. What is the value of tool life index for cutting cast iron by cemented carbide tool? (सीमेंटेड कार्बाइड टूल द्वारा कच्चा लोहा काटने के लिए टूल लाइफ इंडेक्स का मान क्या है?)

42 / 76

42. यदि कार्य के सिरे पर काउंटर सिद्धि करने की अनुमति ना हो तो क्या प्रयोग कियाजाए (What should be used if counter accomplishment is not allowed at the end of the task?)

43 / 76

43. What type of thread can be produced by a die? (डाई से किस प्रकार का धागा बनाया जा सकता है?)

44 / 76

44. Which type of thread is produced by tap and die? (टैप और डाई विधि से किस प्रकार का धागा बनता है?)

45 / 76

45. मीट्रिक चेसिंग डायल ब्रिटिश चेसिंग डायल से किस तरह भिन्न है? (How is a metric chasing dial different from a British chasing dial?)

46 / 76

46. Calculate the driven gear to cut 1.5mm pitch thread on a job using a lathe having lead screw of 4mm pitch with driver gear 30 teeth? (4 मिमी पिच वाले लीड स्क्रू और 30 दांतों वाले ड्राइवर गियर से युक्त लेथ मशीन का उपयोग करके 1.5 मिमी पिच का थ्रेड काटने के लिए आवश्यक ड्राइव गियर की गणना करें?)

47 / 76

47. चूड़ी का नाम क्या है? (What is the name of the bangle?)

48 / 76

48. A thread is represented as M12 x 1.5. What does represent the letter 12? (एक धागे को M12 x 1.5 के रूप में दर्शाया गया है। अक्षर 12 को किससे दर्शाया जाता है?)

49 / 76

49. SQ60x9 वर्गाकार चूड़ी की गहराई कितनी होगी (What will be the depth of SQ60x9 square bangle? )

50 / 76

50. Find the gears for simple gear train, if pitch of lead screw is 6 mm and pitch of thread to be cut is 2 mm? (यदि लीड स्क्रू की पिच 6 मिमी और काटे जाने वाले थ्रेड की पिच 2 मिमी है, तो सरल गियर ट्रेन के लिए गियर ज्ञात कीजिए?)

51 / 76

51. 7/16" लीड वाली चूड़ी काटने के लिए वांछित चेंज गियर की गणना कीजिये यदि लेथ के लीड स्क्रू 4 TPI का‌ हो । (Calculate the change gear required for cutting 7/16" lead bangle if the lead screw of the lathe is 4 TPI.)

52 / 76

52. ब्रिटिशयेड चसिंग डायल अंको वाले कितने विभाजन होते हैंविभाजन होते है? (How many divisions are there with British moving dial numbers?)

53 / 76

53. Calculate the change gear (driver gear) if driven gear has 120 teeth to cut 3mm pitch on a job using lathe having 6 mm pitch lead screw? (यदि ड्राइव गियर में 120 दांत हैं और 6 मिमी पिच वाले लीड स्क्रू वाली लेथ मशीन का उपयोग करके 3 मिमी पिच की कटिंग करनी है, तो चेंज गियर (ड्राइवर गियर) की गणना करें?)

54 / 76

54. एक पौस कोन में अपएर्षक को एक साथ रखने के लिए ज्ञानगी क्या है? (What is the wisdom in putting together the aphrodisiacs in a pot?)

55 / 76

55. Which angle is provided on the metric screw thread micrometer anvil? (मेट्रिक स्क्रू थ्रेड माइक्रोमीटर एनविल पर कौन सा कोण प्रदान किया जाता है?)

56 / 76

56. What is the tool life index of cemented carbide tool for turning high carbon steel? (उच्च कार्बन स्टील की टर्निंग के लिए सीमेंटेड कार्बाइड टूल का टूल लाइफ इंडेक्स क्या है?)

57 / 76

57. What is the depth of ACME thread of 1” major diameter 6TPI? (1 इंच मेजर डायमीटर 6 टीपीआई वाले एसीएमई थ्रेड की गहराई कितनी होती है?)

58 / 76

58. 4 मिमी पिच वाली चूड़ी काटने के लिए वांछित चेंज गियर की गणना कीजिये यदि लेथ कि लेड स्कु की पिच +G46:D484 मिमी हो ओर स्टग बियर (डाइबर‌ 50‌ दातो‌ का हो) (Calculate the required change gear for cutting 4 mm pitch bangle if the pitch of lead screw of lathe is +G46:D484 mm and stud bear (diaber is 50 teeth))

59 / 76

59. आंशिक पिच चुढ़ी के लिए गियर अनुपात विभाजन होते है? (What are the gear ratio divisions for partial pitch clutch?)

60 / 76

60. चूड़ी कर्तन के दौरान बिना हाफ नट। को डिसइंगेज किए मशीन को रिवर्स करने का क्या परिणाम होगा? (Without half nut during bangle cutting. What will be the result of reversing the machine after disengaging it?)

61 / 76

61. B.S.W चूड़ी का क्या उपयोग है? (What is the use of B.S.W bangle?)

62 / 76

62. 60 x 5 mm पिच की वीकार धूली की गहराई कितनी होगी कितनी होगी? (What will be the depth of Vikar Dhuli of 60 x 5 mm pitch?)

63 / 76

63. Calculate the driven gear to cut 2mm pitch on a job using a lathe having lead screw of 4mm pitch with driven gear 50 teeth? (4 मिमी पिच वाले लीड स्क्रू और 50 दांतों वाले ड्राइव गियर से लैस लेथ मशीन का उपयोग करके 2 मिमी पिच की कटिंग करने के लिए आवश्यक ड्राइव गियर की गणना करें?)

64 / 76

64. What is the core diameter of BSW thread of 1” outer dia and 8 TPI? (1 इंच बाहरी व्यास और 8 टीपीआई वाले बीएसडब्ल्यू थ्रेड का कोर व्यास क्या है?)

65 / 76

65. What percentage of cutting speed is reduced for tool life doubling? (टूल की लाइफ को दोगुना करने के लिए कटिंग स्पीड में कितने प्रतिशत की कमी करनी होगी?)

66 / 76

66. Calculate the driven gear to cut 1.5mm pitch thread on a job using a lathe having lead screw of 5mm pitch with driver gear of 30 teeth? (5 मिमी पिच वाले लीड स्क्रू और 30 दांतों वाले ड्राइवर गियर से युक्त लेथ मशीन का उपयोग करके 1.5 मिमी पिच का थ्रेड काटने के लिए आवश्यक ड्राइव गियर की गणना करें?)

67 / 76

67. Which is the method to produce accurate internal thread? (सटीक आंतरिक थ्रेड बनाने की विधि कौन सी है?)

68 / 76

68. 4मिमी पिच चूड़ी काटने के लिए (ड्रैगन गियर ) गैर की गणना कीजिए यदि लेट लीड स्क्रु पिच 4 मिमी हो या ओर ड्रैगन गियर 60 दांतो दांतो का हो (For cutting 4mm pitch bangle (Dragon Gear) calculate the gear if late lead screw pitch is 4mm or dragon gear is 60 teeth.)

69 / 76

69. Which parameter of a thread is measured by three wire method? (तीन तार विधि द्वारा धागे के किस पैरामीटर को मापा जाता है?)

70 / 76

70. What is the purpose of using taper parallels in thread measurement? (धागे की माप में टेपर पैरेलल का उपयोग करने का उद्देश्य क्या है?)

71 / 76

71. Which is the chip less method of thread production? (धागे के उत्पादन की चिप रहित विधि कौन सी है?)

72 / 76

72. What are the uses of B.S.P thread? (बसपा थ्रेड के क्या-क्या उपयोग हैं?)

73 / 76

73. What is the thread form cut by using chasers? (चेज़र का उपयोग करके किस प्रकार का धागा काटा जाता है?)

74 / 76

74. Which method of threading is used in mass production? (बड़े पैमाने पर उत्पादन में धागा पिरोने की कौन सी विधि का उपयोग किया जाता है?)

75 / 76

75. Which one is the example for transmission of motion using thread ? (इनमें से कौन सा उदाहरण धागे के माध्यम से गति के संचरण का है?)

76 / 76

76. Find the change gear (driven gear) to cut 2.5mm pitch thread using a lathe having lead screw of pitch 5mm with driver gear 60 teeth? (5 मिमी पिच वाले लीड स्क्रू और 60 दांतों वाले ड्राइवर गियर से लैस लेथ मशीन का उपयोग करके 2.5 मिमी पिच का थ्रेड काटने के लिए आवश्यक चेंज गियर (चालित गियर) ज्ञात कीजिए?)

Your score is

The average score is 0%

0%

nimi mock test iti turner

Other forms of Thread

कुल प्रश्न - 50

समय - 60 मिनट

1 / 28

1. What is the reason for providing buttress thread in carpentry vice? (बढ़ईगीरी के वाइस में बट्रेस थ्रेड प्रदान करने का कारण क्या है?)

2 / 28

2. What will happen if threading tool is set below center height? (यदि थ्रेडिंग टूल को केंद्र की ऊंचाई से नीचे सेट किया जाए तो क्या होगा?)

3 / 28

3. What is the reason for using ACME thread in lathe lead screw? (लेथ लीड स्क्रू में ACME थ्रेड का उपयोग करने का कारण क्या है?)

4 / 28

4. What is the core dia of square thread 75 x 11 mm pitch? (75 x 11 मिमी पिच वाले वर्गाकार धागे का कोर व्यास कितना है?)

5 / 28

5. What is the depth of square thread 60 x 5 mm pitch? (60 x 5 मिमी पिच वाले वर्गाकार धागे की गहराई कितनी होती है?)

6 / 28

6. What is the core dia of square thread 62 x 10 mm pitch? (62 x 10 मिमी पिच वाले वर्गाकार धागे का कोर व्यास कितना है?)

7 / 28

7. What is the width of the tool to cut square thread of 30 x 3 mm pitch? (30 x 3 मिमी पिच के वर्गाकार धागे को काटने के लिए आवश्यक उपकरण की चौड़ाई कितनी होनी चाहिए?)

8 / 28

8. What is the width of the tool to cut a square thread of 60 x 9 mm pitch? (60 x 9 मिमी पिच वाले वर्गाकार धागे को काटने के लिए आवश्यक उपकरण की चौड़ाई कितनी होनी चाहिए?)

9 / 28

9. What is the relationship between pitch and depth of a square thread? (वर्गाकार धागे की पिच और गहराई के बीच क्या संबंध है?)

10 / 28

10. Calculate the depth of buttress thread 60 mm diameter of 9 mm pitch? (60 मिमी व्यास और 9 मिमी पिच वाले बट्रेस थ्रेड की गहराई की गणना करें?)

11 / 28

11. Calculate the depth of buttress thread diameter 30 mm of pitch 3mm? (30 मिमी व्यास और 3 मिमी पिच वाले बट्रेस थ्रेड की गहराई की गणना करें?)

12 / 28

12. Which device uses buttress thread? (कौन सा उपकरण बट्रेस थ्रेड का उपयोग करता है?)

13 / 28

13. What is calculated by formula 0.75 x pitch? (0.75 x पिच के सूत्र से क्या गणना की जाती है?)

14 / 28

14. What is the relationship between pitch and depth of a buttress thread? (बट्रेस थ्रेड की पिच और गहराई के बीच क्या संबंध है?)

15 / 28

15. Calculate the width of flat of buttress thread 6 mm pitch? (6 मिमी पिच वाले बट्रेस थ्रेड के फ्लैट की चौड़ाई की गणना करें?)

16 / 28

16. Calculate the flat width of 10 mm pitch buttress thread? (10 मिमी पिच वाले बट्रेस थ्रेड की फ्लैट चौड़ाई की गणना करें?)

17 / 28

17. Which formula is to find crest width of ACME thread? (ACME धागे की शिखर चौड़ाई ज्ञात करने का सूत्र क्या है?)

18 / 28

18. Which type thread is used in lathe lead screw? (लेथ लीड स्क्रू में किस प्रकार के थ्रेड का उपयोग किया जाता है?)

19 / 28

19. Which formula is used to find depth of ACME thread? (ACME धागे की गहराई ज्ञात करने के लिए किस सूत्र का उपयोग किया जाता है?)

20 / 28

20. What is the thread depth of square thread SQ60x9? (SQ60x9 वर्गाकार थ्रेड की थ्रेड डेप्थ कितनी है?)

21 / 28

21. Which formula is used to find depth of buttress thread? (बट्रेस थ्रेड की गहराई ज्ञात करने के लिए किस सूत्र का उपयोग किया जाता है?)

22 / 28

22. Which formula is used to find crest width of a buttress thread? (बट्रेस थ्रेड की क्रेस्ट चौड़ाई ज्ञात करने के लिए किस सूत्र का उपयोग किया जाता है?)

23 / 28

23. Which is the angle of buttress thread? (बट्रेस थ्रेड का कोण क्या है?)

24 / 28

24. What does BIS stand for? (BIS का पूरा नाम क्या है?)

25 / 28

25. What is the angle of saw tooth thread? (आरी के दांतों के धागे का कोण क्या है?)

26 / 28

26. What is the shape of buttress thread flank? (बट्रेस थ्रेड फ्लैंक का आकार कैसा होता है?)

27 / 28

27. What is the formula used to find flat width of a buttress thread? (बट्रेस थ्रेड की फ्लैट चौड़ाई ज्ञात करने के लिए किस सूत्र का उपयोग किया जाता है?)

28 / 28

28. Which angle is ground on ACME threading tool? (ACME थ्रेडिंग टूल पर कौन सा कोण ग्राउंड किया जाता है?)

Your score is

The average score is 0%

0%

nimi mock test iti turner

Special Job and Maintenance

कुल प्रश्न - 50

समय - 60 मिनट

1 / 16

1. Which is the cause of small particles of the material become embedded in the space between the grains of the grinding wheel? (पीसने वाले पहिये के दानों के बीच की जगह में पदार्थ के छोटे-छोटे कण क्यों फंस जाते हैं?)

2 / 16

2. What is the material to hold the abrasive particles together in a grinding wheel? (ग्राइंडिंग व्हील में अपघर्षक कणों को एक साथ बांधे रखने के लिए किस पदार्थ का उपयोग किया जाता है?)

3 / 16

3. Which type of center is used in the end of the job if no counter sink hole is permitted? (यदि काउंटर सिंक होल की अनुमति नहीं है, तो काम के अंत में किस प्रकार के सेंटर का उपयोग किया जाता है?)

4 / 16

4. Which mechanism is used for converting linear motion into rotary motion in plunger dial gauge? (प्लंजर डायल गेज में रैखिक गति को घूर्णी गति में परिवर्तित करने के लिए किस तंत्र का उपयोग किया जाता है?)

5 / 16

5. What is the name of lubrication method? (स्नेहन विधि का नाम क्या है?)

6 / 16

6. What is the schedule of lubrication for lathe bed? (लेथ बेड के लिए लुब्रिकेशन का शेड्यूल क्या है?)

7 / 16

7. Which chuck is mainly used for getting a very effective grip over the job? (काम पर बहुत प्रभावी पकड़ बनाने के लिए मुख्य रूप से किस चक का उपयोग किया जाता है?)

8 / 16

8. Which is used to support hollows end jobs? (जिसका उपयोग खोखले सिरे वाले कार्यों को सहारा देने के लिए किया जाता है?)

9 / 16

9. Which is the term used to express grinding wheels to hold the abrasive particle together? (अपघर्षक कणों को एक साथ बांधे रखने के लिए उपयोग किए जाने वाले ग्राइंडिंग व्हील को व्यक्त करने के लिए किस शब्द का प्रयोग किया जाता है?)

10 / 16

10. Which wheel is used for grinding tough materials? (कठोर पदार्थों को पीसने के लिए किस प्रकार के पहिये का उपयोग किया जाता है?)

11 / 16

11. Which bonding material is not affected by water, acid or normal temperature? (कौन सा बंधन पदार्थ पानी, अम्ल या सामान्य तापमान से अप्रभावित रहता है?)

12 / 16

12. What term indicate actual size of the abrasive grain? (अपघर्षक कण के वास्तविक आकार को दर्शाने वाला शब्द क्या है?)

13 / 16

13. What is the name of chuck that hardened steel sleeve having slits cut partly? (उस चक का नाम क्या है जिसमें आंशिक रूप से कटे हुए स्लिट वाली कठोर स्टील की स्लीव लगी होती है?)

14 / 16

14. Which mandrel is used for machining similar part where internal diameter vary slightly? (ऐसे समान पुर्जों की मशीनिंग के लिए किस प्रकार के मैंड्रेल का उपयोग किया जाता है जिनका आंतरिक व्यास थोड़ा भिन्न होता है?)

15 / 16

15. Which mandrels is NOT used in between lathe centers? (लेथ सेंटर के बीच में कौन से मैंड्रेल का उपयोग नहीं किया जाता है?)

16 / 16

16. Which mandrel is manufactured in order to reduce the number of mandrel? (मैंड्रेल की संख्या कम करने के लिए किस प्रकार के मैंड्रेल का निर्माण किया जाता है?)

Your score is

The average score is 0%

0%

Leave a Comment

Your email address will not be published. Required fields are marked *